Configuring ASE CSU/DSU T1 VisualUptime Service

By klsh on January 11, 2007 11:11 AM | | Comments (0)

Configuring Visual Uptime CSU/DSU


I have configured and installed quite a few of these interfaces. They're not hard to work with, and here are a few pointers for setting up your T1 interface. Keep in mind some changes are immediate and others require a reboot.



  1. COMMUNITY—-

    >private


  2. Admin> site name

    SITE NAME [] : CIRCUIT-NUMBER-HERE DLCI NUMBER

    Admin> site location

    SITE LOCATION [] : CITY, State ZIP+4


    Admin> site contact

    SITE CONTACT [] : Name and Number

  3. IP—-

    >from old—-

    copy ip, subnet and router!

  4. LINK—-

    >frame unless for frame circuits—-

    for point to point HDLC, check,check,check!!!

  5. INBAND—-

    >none—-

    >initial


  6. SLA—-

    >on

  7. T1—-

    >from old

  8. for example:

  9. login: admin—-

    Password: ******


  10. MyTown ATT DLCI 123> ip—-

    LAN interface address [192.168.1.238]:—-

    LAN interface subnet mask [255.255.255.240]:—-

    SLIP interface address [NONE]:—-

    SLIP interface subnet mask [255.255.0.0]:—-

    Primary router address [192.168.1.229]: DON’T HIT ENTER UNTIL YOU VERIFY THIS

  11. MyTown ATT DLCI 123> t1—-

    Network Coding (AMI, B8ZS) [B8ZS] :—-

    Network Framing (ESF, D4) [ESF] :—-

    Network Line Build Out (0,-7.5,-15,-22.5) [0 dB] :—-

    Network FDL Protocol (ANSI, AT&T, Both, None) [AT&T TR54016] :—-

    Network Timing (Loop, Internal, DSX1) [Loop] :—-

    Data Channel Rate [64K] :—-

    note!!!! this is port size not the pvc!!!—-

    Data Channels [1-4 (256K)] :—-

    DSX1 Coding (AMI, B8ZS) [B8ZS] :—-

    DSX1 Framing (ESF, D4) [ESF] :—-

    DSX1 Channels [NONE] :—-

    DSX1 Line Build Out (133,266,399,533,655) Less Than [133 feet] :


  12. MyTown ATT DLCI 123>

  13. REBOOT



MySite 123 CarrierName> show

APPFILTER

App Filters are DISABLED.

Application FLOWS and SERVERS will be
collected for all hosts in all subnets.

Local Subnets
==================

COMMUNITY

Read-Write Community : private
Public read-only : Yes
Read-Only Community : public

EVENT

Elapsed Time Event Description
------------ -----------------
0d-05:29:06 Frame relay link is UP
0d-05:29:16 Frame relay link is ROUTER DOWN
0d-05:29:28 Frame relay link is LMISOLATE ACTIVE.ROUTER DOWN
0d-19:32:00 Frame relay link is NETWORK DOWN
0d-19:32:18 Frame relay link is LMISOLATE ACTIVE.ROUTER DOWN
0d-19:32:23 Signal change: T1 OK
0d-19:32:23 Reboot

FRAME

Link Statistics
Near Octets: 345136 Far Octets: 31694
Near Frames: 22181 Far Frames: 1981
Near Frame Errors: 2 Far Frame Errors: 0
Near Aborted Frames: 0 Far Aborted Frames: 0
Near Short Frames: 0 Far Short Frames: 0
Near Long Frames: 0 Far Long Frames: 0
Current Utilization: 0.00 Current Utilization: 0.00
Maximum Utilization: 0.01 Maximum Utilization: 0.01
Current Frames/sec: 0 Current Frames/sec: 0
Maximum Frames/sec: 1 Maximum Frames/sec: 1
Drop Events: 0
Link State: Up
Port Unavailable Secs: 50552
Frame Relay LMI is working correctly.
0 frame relay circuits were reported.

ID
Visual UpTime Select Multiprotocol T1 CSU DROP & INSERT ASE

Software version: M 2.0.023 - Feb 07 2006
Serial Number: 0049-0000000
Installed memory: 64M

Protected by U.S. patents: 5,867,483; 5,521,907; 6,058,102;
6,147,998; and 6,564,214.

This product may also be protected by other U.S. or foreign patents.

Copyright (c) 2006 Fluke Corporation(R).
All Rights Reserved.

LAN interface IP Address: 192.168.1.21
LAN interface Subnet Mask: 255.255.255.0
INBAND interface IP Address: NONE
INBAND interface Subnet Mask: 255.255.255.255
Default Router IP Address: 192.168.1.1

Running for 0 days 19 hours 33 minutes 4 seconds

INBAND
In-band communication: NONE
LMIsolate: INITIAL
Router timeout: 30

IP
Management IP address: 192.168.1.21
Management IP subnet mask: 255.255.255.0
SLIP interface address: NONE
SLIP interface subnet mask: 255.255.0.0
Primary router address: 192.168.1.1

IP Statistics
In Receives: 64519 Out Requests: 1061
In Delivers: 64517 Out Discards: 0
In Header Errors: 0 Out No Routes: 0
In Address Errors: 0 Reassemble Requests: 10
In Unknown Protocols: 0 Reassemble Oks: 5
In Discards: 0 Reassemble Fails: 0
Datagrams Fragmented: 5 Forwarded Datagrams: 0
Fragments Created: 10
Fragment Fails: 0

LINK

Link interface type: Frame

LOOP
T1 Network Loopback: None
Data Port Loopback: None

PASSWD

SECURITY
The security table is empty

Host address security is DISABLED

SERIAL
Console/SLIP speed : 19200

SITE
NAME: MySite 123 CarrierName
LOCATION:
CONTACT:

SLA
Inter-ASE messaging: ON
Message octets: 200

SLIP
Connection Type : Dial

STATUS
This ASE has been running for 0d-19:33:04.
T1 network side interface: OK.
V.35 data side interface: OK.
Frame Relay LMI is working correctly.

T1
Network Coding : B8ZS
Network Framing : ESF
Network Line Build Out : 0 dB
Network FDL Protocol : AT&T TR54016
Network Timing : Loop
Data Channel Rate : 64K
Data Channels : 1-24 (1536K)
DSX1 Coding : B8ZS
DSX1 Framing : ESF
DSX1 Channels : NONE
DSX1 Line Build Out : 133 feet

Network DSX1
------- ----
Signal OK Disabled
Excess Zeros OK Disabled
Frame Sync OK Disabled
Yellow Alarm Rx No No
Yellow Alarm Tx No No
Blue Alarm Rx No No
Blue Alarm Tx N/A No
Looped Back No No
B8ZS Detected No No
BPVs 0 0
CRC Errors 0 0
SESs 0 0
ESs 0 0
ESBs 0 0
Unavail Secs 0 0
Frame Slips 0 0

V35
Transmit Clock Source : SCT
Polarity: Normal
RLSD : Normal
Rate : 1536 Kbps
Activity: SD: Yes RD: Yes SCLK: Yes RCLK: Yes
Signals: RTS: Yes CTS: Yes DSR: Yes RLSD: Yes
DTR: Yes LL: No


Categories:

Leave a comment

About this Entry

This page contains a single entry by klsh published on January 11, 2007 11:11 AM.

Windows XP WPA/WPA2/IEEE 802.1X Supplicant was the previous entry in this blog.

EEM is flexible system designed to customize IOS : Embedded Event Manager is the next entry in this blog.

Find recent content on the main index or look in the archives to find all content.

Powered by Movable Type 4.01

Search