Log on to Cisco CATALYST 6500 Switch and check port ARP and MAC for IP

By klsh on May 4, 2009 3:47 PM | Permalink | TrackBacks (0)

I recently had to check a port on a catalyst:

CISCO6500# SHOW VER Cisco Internetwork Operating System Software IOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by cisco Systems, Inc. Compiled Thu 23-Nov-06 06:34 by kellythw Image text-base: 0x40101040, data-base: 0x42A70000

ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1) BOOTLDR: s72033_rp Software (s72033_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)

cisco6500 uptime is 1 year, 7 weeks, 8 hours, 39 minutes Time since cisco6500 switched to active is 1 year, 7 weeks, 8 hours, 40 minutes System returned to ROM by power cycle (SP by power on) System restarted at 06:15:44 EDT Sun Mar 16 2008 System image file is "sup-bootdisk:s72033-ipservices_wan-mz.122-18.SXF7.bin" cisco WS-C6509-E (R7000) processor (revision 1.2) with 458720K/65536K bytes of memory. Processor board ID SMG1042N1X3 SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache Last reset from s/w reset CISCO6500#SHOW INT GIGABITETHERNET 8/27 GigabitEthernet8/27 is up, line protocol is up (connected) Hardware is C6k 1000Mb 802.3, address is 001e.4a9e.9d5a (bia 001e.4a9e.9d5a) Description: SERVER01 (1) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s input flow-control is off, output flow-control is on Clock mode is auto ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters 19w5d Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 1000 bits/sec, 2 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 5127687 packets input, 328174154 bytes, 0 no buffer Received 20 broadcasts (6 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input CISCO6500#SHOW RUN Building configuration... Current configuration : 66705 bytes ! ! Last configuration change at 09:35:07 EDT Thu Apr 9 2009 by mbihs ! NVRAM config last updated at 09:35:55 EDT Thu Apr 9 2009 by mbihs ! upgrade fpd auto version 12.2 no service pad service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption service internal service counters max age 5 ! hostname cisco6500 ! boot system flash sup-bootdisk:s72033-ipservices_wan-mz.122-18.SXF7.bin logging buffered 10000 notifications no logging console enable secret 5 $1$whlJ$E6dSWt7M5eZzZqG9B/VDY2 ! aaa new-model /8/27 FILTERING... interface GigabitEthernet8/27 description SERVER01 (1) switchport switchport access vlan 581 switchport mode access no ip address speed 1000 duplex full no cdp enable spanning-tree portfast spanning-tree bpduguard enable ! CISCO6500#PING SERVER01 Translating "SERVER01"...domain server (192.162.129.27) [OK] CISCO6500#PING 192.164.37.21 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.164.37.21, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms

CISCO6500#SHOW ARP | INCLUDE 192.164.37.21 Internet 192.164.37.21 2 000e.0cdb.67b8 ARPA Vlan581 cisco6500# exit